Go to TOP

UNO R3 Board for Arduino Compatible + CNC V3 Shield + 4x DRV8825 Driver Red + blue

Product code: PHO_0GNYS3GP

$26.37 $31.46 

SOLD OUT
Quantity:
UNO R3 Board for Arduino Compatible + CNC V3 Shield + 4x DRV8825 Driver Red + blue
Ship to: FREE SHIPPING to United States via ePacket (with Battery)  
Supplier:THE CRAFT COMPANY
Rank:4.4
Buy More... Get Lower PricesYes! We Ship To  us

Payment Guarantee:smile
Shipping Support:smile
Share To:
.
UNO R3 Board for Arduino Compatible + CNC V3 Shield + 4x DRV8825 Driver Red + blue
UNO R3 Board for Arduino Compatible + CNC V3 Shield + 4x DRV8825 Driver Red + blue
$26.37 
.

It is a carrier board or breakout board for TI's DRV8825 stepper motor driver.

Recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product.

This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information).

.

Description:

Item type:tool

(1) UNO R3 CH340:
Add two rows of the holes for the pins. So it can be connected with normal Dubond line.
Add 3 rows of the holes for wiring.
Change the in-line package of ATMEGA328P to flat package.
CH340G Replace ATmega16U2
CH340G Driver Download link : check here
(2) CNC Shield
UNO for module IO port correspondence introduction.
IO corresponding figure above
UNO for Arduino expansion board
EN ( stepper motor driver enable , active low )
Z.DIR (Z -axis direction control )
Y.DIR (Y -axis direction control )
X.DIR (X -axis direction control )
Z.STEP (Z -axis stepper control )
Y.STEP (Y -axis stepper control )
X.STEP (X -axis stepper control )
(3) DRV8825
1)Simple step and direction control interface
2)Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
3)Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates
4)45 V maximum supply voltage
5)Built-in regulator (no external logic voltage supply needed)
6)Can interface directly with 3.3 V and 5 V systems
7)Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
8)Short-to-ground and shorted-load protection
9)4-layer, 2 oz copper PCB for improved heat dissipation
10)Exposed solderable ground pad below the driver IC on the bottom of the PCB
11)Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information)

Package includes:

1 x UNO R3 Board for Arduino Compatible + CNC V3 Shield + 4x DRV8825 Driver

.

Customer Reviews(0)

5 out of 5
5 star rating 5 star rating 5 star rating 5 star rating 5 star rating
UNO R3 Board for Arduino Compatible + CNC V3 Shield + 4x DRV8825 Driver Red + blue
Deliverystarrs 5starrs 5starrs 5starrs 5starrs 5
Value for Moneystarrs 5starrs 5starrs 5starrs 5starrs 5
Packagingstarrs 5starrs 5starrs 5starrs 5starrs 5
Ease of Setup/Usestarrs 5starrs 5starrs 5starrs 5starrs 5
Function/Performancestarrs 5starrs 5starrs 5starrs 5starrs 5
Write Review
Date Launched: Jun 01 2020
Previous     Next
All categories 