Go to TOP

This product is out of stock, and not coming back.
It may have been replaced by a newer version, see replacement/alternatives listed below.

ANENG VD901 AC 12V-1000V Electrical Non Contact Voltage Detector Test Pen Probe Tester yellow

Product code: PHO_0CS5UIVU
OUT OF STOCK
.
ANENG VD901 AC 12V-1000V Electrical Non Contact Voltage Detector Test Pen Probe Tester yellow
ANENG VD901 AC 12V-1000V Electrical Non Contact Voltage Detector Test Pen Probe Tester yellow
$12.17 
.

AC voltage detection range selection, when the tester is turned on: about 48 ~ 1000V.Gently press the switch key (S) , and the indicator is on. The voltage range is about 12 ~ 1000V.

When the tester is not operated for about 5 minutes and no voltage signal is detected, the tester will shut down automatically.

When the battery voltage is lower than about 2.6v, the power indicator flashes for 3 times, and the buzzer will automatically shut down. Please replace the battery in time.

.

Description:

Item type: Test Pen

Package includes:

1 * Test Pen

Notes:

Operating instructions:
1. start the tester: press the power on key, self-check the tester, flashlight, indicator light of induced voltage signal, signal strength indicator light (high, medium and low), the button indicator light flashes once at the same time, and the power indicator light is always on.Turn off the tester: when the tester is on, press the power on key and it is off.
2. Under the starting state of tester, press the key to turn on the flashlight and turn on the flashlight.
3. turn off the flashlight: in the flashlight on state, press the flashlight on key, put out the flashlight.If the flashlight is not turned off, it will automatically go out in about 5 minutes.
4. ac voltage detection:
Insert the probe of the tester into a power socket or close to a live wire. When the tester detects ac voltage signal, the indicator light of induced voltage signal flashes. According to the detected signal strength, the tester lights up the corresponding signal strength indicator (high, medium and low), and the buzzer emits alarm sound of different frequencies.When ac voltage signal is sensed, L signal strength indicator light (low) flashes;When a higher ac voltage signal is detected, the M signal strength indicator (middle) is long on;When the highest ac voltage signal is sensed, H signal strength indicator lamp (high) 3 grain lamp flashes.
5. Separate the two wires to be tested as far as possible, and then use the probe of the tester to get close to the wire respectively. If it is a socket, insert the probe into the socket. The tester detects the wire with strong induction signal, and the zero wire with weak or no induction signal.

1-2cm error might exist due to manual measurements, please kindly understand. The colors deviation might differ due to different monitor settings.

.

Customer Reviews(0)

5 out of 5
5 star rating 5 star rating 5 star rating 5 star rating 5 star rating
ANENG VD901 AC 12V-1000V Electrical Non Contact Voltage Detector Test Pen Probe Tester yellow
Deliverystarrs 5starrs 5starrs 5starrs 5starrs 5
Value for Moneystarrs 5starrs 5starrs 5starrs 5starrs 5
Packagingstarrs 5starrs 5starrs 5starrs 5starrs 5
Ease of Setup/Usestarrs 5starrs 5starrs 5starrs 5starrs 5
Function/Performancestarrs 5starrs 5starrs 5starrs 5starrs 5
Write Review
Date Launched: Sep 24 2019
Previous     Next
All categories   

categories

Local Warehouse

Business & Industrial

Consumer Electronics

Cellphone & Accessories

Tablet PCs & Accessories

Automobiles & Motorcycles

Computer & Networking

Home Garden & Tools

Drones & Cool Gadgets

Sports & Outdoors

Health & Beauty

Apparel & Jewelry

Special Supplies