Go to TOP

1800w Induction Heater Pcb Board Module Flyback Driver Heater Induction Heating Machine

Product code: PHO_0QA25GVJ

$69.66 $79.88 

SOLD OUT
Quantity:
1800w Induction Heater Pcb Board Module Flyback Driver Heater Induction Heating Machine
Ship to: FREE SHIPPING to United States via CHINA POST - Packet NO Tracking  
Supplier:Leonard Veblen
Rank:4.3
Buy More... Get Lower PricesYes! We Ship To  us

Payment Guarantee:smile
Shipping Support:smile
Share To:
.
1800w Induction Heater Pcb Board Module Flyback Driver Heater Induction Heating Machine
1800w Induction Heater Pcb Board Module Flyback Driver Heater Induction Heating Machine
$69.66 
.

Stable performance: The heating plate is made of military-grade PCB, and the performance is stable

Design: The power line is fully covered with copper cover design, which can increase the current and heat generation

Good heat dissipation:Using oversized and large power heat sink to dissipate heat better

High power: Using six IRFP260 and 12 capacitors in parallel resonance, the power is high and the efficiency is high

.

Description:
product Category: Heating Machine
Model: a52357
Product description
Material: metal + plastic
Color: Black
Input voltage: 12v-48v above 36V is recommended
Power requirements: less than 12V ≥ 10a, 15V or more than 20A
Maximum power: 1800W
Maximum current: 50A
Size: 25x12x9cm (manual measurement, error about 3mm, please understand)
features:
The heating plate is made of military PCB with stable performance;
The power line is completely covered with copper design, which can increase the generation of current and heat;
Large size and better heat dissipation;
The output terminal uses three M4 copper pillars in parallel, which can be connected to other outputs, such as high voltage battery pack;
With six irfp260 and 12 parallel resonant capacitors, it has high power and high efficiency;
be careful:
The heating power is very high, in addition to the plate and components are very hot, and the heat of copper tube is also very high. The buyer can prepare the cooling system separately, and can purchase small water pump and 4mm rubber hose with inner diameter of 2m.
2. When using the switching power supply, it should be noted that the high-power switching power supply generally has the soft start function, and the same output voltage will increase slowly. If the voltage rises to 10V too early, the circuit will not bear vibration, and the conduction of two MOS tubes and components will burn at the same time, please change the voltage stability of the power supply, and then enter the induction heating circuit.
3. When heating metal objects, do not heat too much metal, otherwise it may lead to power overload. Please install 35A fuse or ammeter, and it is better to use air switch. (packing not included)
4. Although the drive board can withstand more than 40A current, it is recommended not to exceed 48V 35A to avoid accidents and damage.
5. The packaging box has a diameter of 60mm heating circle, and the design voltage is 36V. If a power supply of more than 40 V is used, it will be used for the inner diameter of the pump which is 70mm larger than the heating circle. The 12V DC power supply is used for the water, and the independent power regulator module is used to burn the fan and water pump.
6. The minimum input voltage of the module is 12V, which does not mean that the whole 12V power supply can be used. Some novice buyers can use smaller power supply. This module has specific voltage and current requirements. Its 12V voltage and current should be greater than 10A. It can use the power supply. If the power is too low, the power output will be greatly reduced. When the voltage is less than 12V, two MOS transistors will be generated at the same time, which will burn the MOS transistors
7. If the MOS tube is found to have a fever, the first thing to consider is whether the power output meets the requirements.
8. Do not empty the circuit board, otherwise it will emit high frequency noise, and then the MOS tube will burn out.
9. It is recommended to use 36V 20A power supply for induction heating. The 12V power supply is too small, almost no response. The 12V power supply is easy to reduce the output voltage of the power supply, and it is very dangerous to be lower than 12V
10. The power of induction heating is high, so the fever is normal. Please make sure to heat well. For induction heating, it is recommended that the power supply should be greater than 48V 50a, and the power supply should be replaced. The higher the voltage, the higher the current, the higher the heating power and the faster the heating speed.
Application: high frequency induction heating plate
How to use it? (description)
For induction heating, it is recommended to use a switching power supply of 48V50A or higher. If the power supply is 24V or more, a power supply of 20A or more is required. The higher the voltage, the larger the current, the higher the heating power, the faster the heating speed.
Content:
1*PCB board (with dual fans) 
1* copper tube
Note: All images and descriptions are for illustrative purposes only. The color deviation is subject to actual system configuration and slight dimension difference is allowed due to manual measurement.

.

Customer Reviews(0)

5 out of 5
5 star rating 5 star rating 5 star rating 5 star rating 5 star rating
1800w Induction Heater Pcb Board Module Flyback Driver Heater Induction Heating Machine
Deliverystarrs 5starrs 5starrs 5starrs 5starrs 5
Value for Moneystarrs 5starrs 5starrs 5starrs 5starrs 5
Packagingstarrs 5starrs 5starrs 5starrs 5starrs 5
Ease of Setup/Usestarrs 5starrs 5starrs 5starrs 5starrs 5
Function/Performancestarrs 5starrs 5starrs 5starrs 5starrs 5
Write Review
Date Launched: Jan 06 2021
Previous     Next
All categories 