Go to TOP

Holybro Kakute F7 Flight Controller & 65A BL_32 Tekko32F3 Metal 4in1 ESC 4-6S Stack Combo for RC Drone FPV Racing KSX3220

Product code: PTO_057JYJ31
Flash Deals2092160

$50.99  $121.09 $144.39 

SOLD OUT
65% OFF
Quantity:
1 in stock
Holybro Kakute F7 Flight Controller & 65A BL_32 Tekko32F3 Metal 4in1 ESC 4-6S Stack Combo for RC Drone FPV Racing KSX3220
Ship to: FREE SHIPPING to United States via YUNTU--Special Priority Line Registration  
Supplier:Fressco
Rank:4.5
Buy More... Get Lower PricesYes! We Ship To  us

Payment Guarantee:smile
Shipping Support:smile
Share To:
.
Holybro Kakute F7 Flight Controller & 65A BL_32 Tekko32F3 Metal 4in1 ESC 4-6S Stack Combo for RC Drone FPV Racing KSX3220
65%
OFF
Holybro Kakute F7 Flight Controller & 65A BL_32 Tekko32F3 Metal 4in1 ESC 4-6S Stack Combo for RC Drone FPV Racing KSX3220
$50.99  $121.09 
.

High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate.

Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.

2 oz. copper PCB allows up to 120A maximum continuous current.

Dedicated bootloader button for easy firmware flashing.

.

Description:

Item type:Kakute F7 flight controller

Brand Name: Holybro

Item Name: F7 Flight Controller 65A 4 in 1 ESC Stack

Kakute F7 Flight Controller ( Manual )

Brand name: Holybro

Item name: Kakute F7

MCU: STM32F745 32-bit processor

IMU: ICM20689 (SPI)

Barometer: BMP280

USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 6 hardware UARTS (UART1,2,3,4,6,7)

All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.

Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.

TF card for Blackbox logging

Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)

Mounting Holes: Standard 30.5mm square to center of holes

Weight: 9g

Features:

Supports Betaflight, Butterflight, and Cleanflight.

Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.

Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.

High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate.

Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.

2 oz. copper PCB allows up to 120A maximum continuous current.

Dedicated bootloader button for easy firmware flashing.

Low-profile design fits into even very compact frames.

Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).

Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.

Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.

Supports BLHeli pass-through for easy ESC upgrade and configuration.

Tekko32F3 Metal 4in1 ESC

Brand Name: Holybro

Model: Tekko32F3 Metal

Item Name: 65A BL_32 32Bit DShot1200 4 in 1 ESC

Con. Current: 65A

Peak Current: 80A

Input Voltage: 4-6S Lipo Support

Ext. cap needed for 6s (470uf 35v for 6s usage)

F3(M4 Core) MCU, Runs BLHELI32 firmware, the MCU works at 108Mhz

Size: 42x42mm

Mounting Hole: 30.5x30.5mm

Weight: 12g

Notice:

1. The air flow is very import if you want to run this 4in1 in high current.

2. The input cable(from lipo to 4in1), should be good soldered, and at least 12AWG

3. Please use non-metallic isolation standoffs (marked in red in the diagram above) for the mounting holes on the ESC.

Because mounting holes and motor pad are connected.

Features:

The 4in1 has onboard analog current sensor, and TLM function(then no current reading over TLM)

Using metal case mosfet for better Heat dissipation

BLheli_32 firmware, support Oneshot, Multishot, Dshot150, DShot300, DShot600 and DShot1200

Package Include:

1x Kakute F7 flight controller

1x Tekko32 F3 Metal 4in1 ESC

1x 470uF 35V Electrolytic Capacitor

1x 8pin to 8pin 1mm pitch 65mm Cable

1x 8pin to 8pin 1mm pitch 25mm Cable

Note:

The colors deviation might differ due to different monitor settings.

.

Customer Reviews(0)

5 out of 5
5 star rating 5 star rating 5 star rating 5 star rating 5 star rating
Holybro Kakute F7 Flight Controller & 65A BL_32 Tekko32F3 Metal 4in1 ESC 4-6S Stack Combo for RC Drone FPV Racing KSX3220
Deliverystarrs 5starrs 5starrs 5starrs 5starrs 5
Value for Moneystarrs 5starrs 5starrs 5starrs 5starrs 5
Packagingstarrs 5starrs 5starrs 5starrs 5starrs 5
Ease of Setup/Usestarrs 5starrs 5starrs 5starrs 5starrs 5
Function/Performancestarrs 5starrs 5starrs 5starrs 5starrs 5
Write Review
Date Launched: Jun 02 2020
Previous     Next
All categories 