Go to TOP

Holybro Kakute F7 AIO V1.5 Flight Controller OSD PDB+Atlatl HV V2 5.8G FPV Transmitter for RC Drone Kakute F7

Product code: PTO_0B6I6E3B

$94.73 $112.80 

SOLD OUT
Quantity:
Holybro Kakute F7 AIO V1.5 Flight Controller OSD PDB+Atlatl HV V2 5.8G FPV Transmitter for RC Drone Kakute F7
Ship to: FREE SHIPPING to United States via YUNTU--Special Priority Line Registration  
Supplier:JYL_SHOP
Rank:4.4
Buy More... Get Lower PricesYes! We Ship To  us

Payment Guarantee:smile
Shipping Support:smile
Share To:
.
Holybro Kakute F7 AIO V1.5 Flight Controller OSD PDB+Atlatl HV V2 5.8G FPV Transmitter for RC Drone Kakute F7
Holybro Kakute F7 AIO V1.5 Flight Controller OSD PDB+Atlatl HV V2 5.8G FPV Transmitter for RC Drone Kakute F7
$94.73 
.

Supports Betaflight, Butterflight, and Cleanflight.

Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.

Dedicated bootloader button for easy firmware flashing.

Low-profile design fits into even very compact frames.

Supports BLHeli pass-through for easy ESC upgrade and configuration.

.

Description:

Item type:Flight Controller

Kakute F7 flight controller:
Click For Kakute F7 AIO V1.5  Manual 
MCU: STM32F745 32-bit processor
IMU: MPU6000 (SPI)
Barometer: BMP280
Current Sensor: Approximately 130 amps maximum measurable value
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
6 hardware UARTS (UART1,2,3,4,6,7)
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on 
any UART without “uninvert hack”.
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not 
supported.
TF card for Blackbox logging
Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 8g
 

Packing list:

1x Kakute f7 AIO V1.5 +Atlatl V2 stack 
1x 80mm SMA-MMCX Cable
1x 150mm 4pin JST GH wire
 

Notes:

Soft-mounting built in. The IMU (gyro) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
High-performance / low-noise / high sensitivity IMU. MPU6000 with 6-axis gyro and accelerometer. 
Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on B+ pad only).
Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 V1.5 monitors voltage directly from the power supply.
Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.

.
Date Launched: Jun 02 2020
Previous     Next
All categories 